'하드디스크추가'에 해당되는 글 1건

CentOS 하드디스크 추가시 마운트하기



기존 하드디스크 이외에 하나더 추가할 경우 포맷하고 마운트를 하여야 합니다.


먼저 fdisk -l 로 Disk 정보를 확인합니다.


[root@vps ~]# fdisk -l


Disk /dev/sda: 1000.2 GB, 1000204886016 bytes

...


Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes

255 heads, 63 sectors/track, 121601 cylinders

Units = cylinders of 16065 * 512 = 8225280 bytes

Sector size (logical/physical): 512 bytes / 4096 bytes

I/O size (minimum/optimal): 4096 bytes / 4096 bytes

Disk identifier: 0x00000000


/dev/sdb 로 확인되었습니다.


이제 파티션을 잡아야 합니다.


[root@vps ~]# fdisk /dev/sdb

Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel

Building a new DOS disklabel with disk identifier 0xbf2eadcc.

Changes will remain in memory only, until you decide to write them.

After that, of course, the previous content won't be recoverable.


Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)


The device presents a logical sector size that is smaller than

the physical sector size. Aligning to a physical sector (or optimal

I/O) size boundary is recommended, or performance may be impacted.


WARNING: DOS-compatible mode is deprecated. It's strongly recommended to

         switch off the mode (command 'c') and change display units to

         sectors (command 'u').


Command (m for help): n

Command action

   e   extended

   p   primary partition (1-4)

p

Partition number (1-4): 1

First cylinder (1-121601, default 1):

Using default value 1

Last cylinder, +cylinders or +size{K,M,G} (1-121601, default 121601):

Using default value 121601


Command (m for help): w

The partition table has been altered!


Calling ioctl() to re-read partition table.

Syncing disks.


굵은파란색을 보시면 됩니다.


파티션을 잡은 뒤에는 포맷을 합니다.


[root@vps ~]# mkfs.ext4 /dev/sdb1

mke2fs 1.41.12 (17-May-2010)

/dev/sdb1 alignment is offset by 512 bytes.

This may result in very poor performance, (re)-partitioning suggested.

Filesystem label=

OS type: Linux

Block size=4096 (log=2)

Fragment size=4096 (log=2)

Stride=1 blocks, Stripe width=0 blocks

61054976 inodes, 244190000 blocks

12209500 blocks (5.00%) reserved for the super user

First data block=0

Maximum filesystem blocks=4294967296

7453 block groups

32768 blocks per group, 32768 fragments per group

8192 inodes per group

Superblock backups stored on blocks:

        32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,

        4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968,

        102400000, 214990848


Writing inode tables: done

Creating journal (32768 blocks): done

Writing superblocks and filesystem accounting information: done


This filesystem will be automatically checked every 30 mounts or

180 days, whichever comes first.  Use tune2fs -c or -i to override.


시간이 조금 걸립니다.


이제 마운트를 하면 됩니다.


uuid 로 마운트를 해볼까요~


[root@vps ~]# blkid /dev/sdb1

/dev/sdb1: UUID="5a76eec0-4b80-d3c4-9de4-302bffcc898c" TYPE="ext4"


UUID 를 복사해서 /etc/fstab 에 아래 처럼 추가합니다.


UUID=5a76eec0-4b80-d3c4-9de4-302bffcc898c /hdd2 ext4 defaults 1 1


/hdd2 는 미리 만들어 주어야 합니다. (mkdir /hdd2)


# mount -a 로 마운트 하면 됩니다.


# df -h 로 제대로 마운트 되었는지 확인합니다.


'LINUX' 카테고리의 다른 글

CentOS 6.x NGINX configtest  (0) 2018.06.01
리눅스 하드디스크 정보보기  (0) 2018.05.29
리눅스 RSYNC 특정 폴더 제외하기  (0) 2018.05.28
CentOS yum install 메모리 에러  (0) 2018.05.25
htaccess 특정IP만 허용하기  (0) 2018.04.12
블로그 이미지

영은파더♥

가상서버호스팅 VPS 리눅스 서버관리 윈도우 IT

,